Recent Activity

Activity stream for all registered members at BinderPlanet.


  1. stroker3 replied to the thread 1973 Wagonmaster MPG question.....

    Thinking something similar was in Revenge of the Nerds but .....whatever you do, avoid having a special spot, insisting on room mate...

    Dec 18, 2017 at 4:27 PM
  2. 67NCScout replied to the thread Alloy USA axle kit stud fitment.

    That was my concern with drilling. Maybe set up a jig for the drill press. I have found several Dorman options that have a knurl...

    Dec 18, 2017 at 4:21 PM
  3. Mattd liked jeffb1051's post in the thread 1977 SSII "resto-mod".

    For the rear, just 4" lift springs, 3/8" u bolt plates, moved the shackle hangers forward 2 1/2" to get the angles and ride height where...

    IMG_4949.JPG IMG_4971.JPG IMG_4973.JPG Dec 18, 2017 at 3:48 PM
  4. stinger75ih replied to the thread Can't get Scout II into 4H.

    If it hasn't been mentioned and a quick easy check, make sure all the transmission and transfer case bellhousing bolts are tight. I had...

    Dec 18, 2017 at 3:05 PM
  5. Darrel liked Kurt_M's post in the thread 1972 IH 1600 Loadstar idling too fast all of a sudden.

    Check the secondary throttle plates, they can stick open just a little and cause high idle. Those governor carbs are a bit different....

    Dec 18, 2017 at 2:49 PM
  6. abarsn180 posted a new thread.

    '72 Loadstar Allison Auto Trans Fluid?

    '72 1600 IH Loadstar w/Allison Automatic, trans fluid is low, wondering if there's a particular trans. fluid recommendation? I have...

    IMG_1126.JPG

    Forum: General IH Tech

    Dec 18, 2017 at 2:49 PM
  7. abarsn180 replied to the thread 1972 IH 1600 Loadstar idling too fast all of a sudden.

    The secondary throttle plates were stuck, once freed it ran perfect. Thanks for all the suggestions!

    Dec 18, 2017 at 2:42 PM
  8. Grizzly replied to the thread Pertronix success.

    That’s because you have an up dated version beware I drove a 22000 lbs school bus 2.800 miles when I was just 10 miles from destination...

    Dec 18, 2017 at 2:26 PM
  9. marduk101567 replied to the thread Daughter/Father Build ’69 800A.

    Part #? Sent from my iPhone using Tapatalk

    Dec 18, 2017 at 2:04 PM
  10. 77IHSCOUT set their location as San Jose, CA.

    Dec 18, 2017 at 1:59 PM
  11. 77IHSCOUT has a new avatar.

    Dec 18, 2017 at 1:56 PM
  12. Darrel replied to the thread Rear Dana 44 inner axle seals.

    With the pinion pointed that far up you pretty much have to fill it higher than factory to ensure you get good slow speed pinion bearing...

    Dec 18, 2017 at 1:45 PM
  13. Randall Barringer replied to the thread Champagne for 2017.

    It is officially back on the road and fully legal. I installed a plastic window guide on the driver´s side, mine was completely missing....

    Dec 18, 2017 at 1:44 PM
  14. Comanche Scott replied to the thread '70 800A Green Machine.

    I think without the weight of the 4BT they would be a bit harsh. They are only 4 leaf packs, and don't have the military wrap. So all...

    Dec 18, 2017 at 1:10 PM
  15. BinderBookie replied to the thread 1973 Wagonmaster MPG question.....

    I think there are studies that show increased drag with overfilling (I can't say by how much) but there are worse effects. Oxidation!...

    Dec 18, 2017 at 1:02 PM
Loading...